"1? should be on the display, press and hold the "Tool" button and the letter "A" Wait until the printer starts to configure itself. Release the "Color Start" button, and then release the "Reset Button". While pressing the "Reset button", press and hold the "Color Start" button. Press and Hold the "Reset button" on the printer. NOTE: Canon MP140 thru MP830 Printer Models Onlyī. Pixma "MP" Printer Series: Universal Ink Counter Reset*** (Procedure #3.d.) Turn off the printer by pushing the power button one more time. Push the ' Stop/Reset ' button four times in a row. Wait approximately 20 to 30 seconds until the LED shows 0. The power button, release the ' Stop/Reset ' button and then push it twice in a row. Hold the ' Stop/Reset ' button while pushing the power button. Press the power button to turn off the printer. NOTE: Select Canon Printer Models that feature an LCD display screen Pixma "MP/MX/MG" Printer Series: Ink Counter Reset*** (Procedure #3.c.) Wait a few minutes for the printer to recognize the cartridges before trying to print.Į. Place the ink cartridges back inside once you see a message that says ' Replace Cartridges. Plug the power cable back in and hit the ' On/Off ' button. Lift out both ink cartridges and close the cover. Lift up the Canon MP 470 printer cover and wait for the cartridges to move to the left.
The Canon printer to print out a test page.į.
Hit the ' Stop/Reset ' button when you see a message that says ' Without Cleaning. Hit the right arrow button until you see ' Shipping Mode 3 ' on the LCD display. This puts the printer into factory mode.ĭ. Hit the ' Stop/Reset ' button two times while holding down the ' On/Off ' button, then let go Press the ' On/Off ' button while you plug the cable back in.Ĭ. Turn off the Canon MP printer and unplug it from the outlet.ī.
NOTE: Most MP200 thru MP400 Series Printer ModelsĪ. Pixma "MP" Printer Series: Ink Counter Reset*** (Procedure #3.b.) Close the cartridge door and release the power button. Reconnect the power cables while still holding down the power button.ĭ. Open the cartridge door and hold down the power button.Ĭ. Unplug the power and the USB cables from the printer.ī. Push the ' Stop/Reset ' button four (4) times in a row.į. Wait approximately 20 to 30 seconds until the LED shows 0.ĭ. Power button, release the ' Stop/Reset ' button and then push it twice in a row.Ĭ. Press the power button to turn off the printer.ī. Pixma MP/MX/MG Series: General Printer & Ink Counter Reset*** (Procedure #3.a)Ī. The blinking ink level/power light should go steady after a fewĬ. Release the Resume (triangle-circle) button. Press and Hold the Power Button hold both buttons for 5 seconds Press and Hold the Resume (triangle-circle) button Pixma iP Ink Counter Reset** (Procedure #2) Printing may continue under the 'ink out' condition.ī. Select 'Stop'/'Reset', 'OK' or the 'Resume' button (triangle-circle icon) on your printer for 5 At computer screen message, select 'Stop'/'Reset', 'OK', or 'Resume',ī. Pixma iP/MP/MX/MG Ink Counter Reset* (UNIVERSAL RESET Procedure #1)Ī. NOTE: for multi-cartridge installation, the procedure(s) may need to be repeated twice.Ī. Ink waste container reset procedures are also provided below. In most cases, the error/alert will need to be cleared to enable The following procedures may be used to reset the Canon printer ink level monitoringįollowing the installation of a refilled Canon 30, 31, 40, 41, 50, 51, 210, 211, 240, or 241 Ma ktoś jakieś sugestie?Ĭanon 30-241 Ink Cartridge Reset - Pixma iP/MP/MX/MG Series Wszystko działało.Tym razem wyskakuje mi na wyświetlaczu E czyli error i 5,nie da rady resetować. Robiłem to już wcześniej z instrukcji resetowania canona,dołączam pdf. Witam! Wymieniłem tusze w tej drukarce,czarny i kolor,odpowiednio 540xxl i 541xxl, zamienniki. Canon MG2155 - Nie chce czytać zamienników.